How To Install Windows Xp On A Sata Drive

Z7_3054ICK0KGTE30AQO5O3KA30N0

HP Notebook PCs - How to Add Series ATA (SATA) Drives to a Windows Installation

This document describes installing native Series ATA (SATA) drives on a computer that is using Windows Vista. Computers congenital for Windows XP use native-ATI technology to control hard drives, while Windows Vista uses native-Serial ATA (SATA) technology. Installing an ATI hard drive on a computer with WINDOWS Vista will cause compatibility problems.

Likewise, if a reckoner is downgraded from Vista to XP, information technology may brandish an error message that the operating system cannot locate a difficult bulldoze. If the installer cannot locate a hard drive, it cannot install the XP operating system. The BIOS on a Vista computer is configured for a native-SATA surroundings and it cannot recognize ATI drivers. It may exist possible to override or change the BIOS settings to let XP to recognize the hard drive.

note:

.

There are 3 methods for installing a SATA drive a Windows installation.

Disable the native-SATA in the BIOS

If the BIOS provides an selection to disable the native-SATA configuration in the BIOS, do the post-obit steps.

1. Turn off the calculator.

2. Press the ability push button and press f10 to open the BIOS Setup.

3. Utilize the cursor to navigate the Configuration options to locate the Native-SATA setting.

4. • If at that place is a SATA setting, select the Disable pick, and then press F10 to save the alter and restart the computer.

   • If at that place is no SATA setting, utilise i of the other options in this document to change the settings.

Stand up Alone Windows Installation

This procedure uses third-party software and is typically performed by home PC users.

1. Make up one's mind the type of processor in the computer, and then search for and download the latest SATA AHCI driver from the processor manufacturer'south web site. Some SATA AHCI drivers are available on the www.hp.com web site. For additional information, HP Notebook PCs - Locating HP Software, Driver and BIOS Updates.

2. Download and install an orthodox file managing director.

   note:

   For this example, Total Commander is used. Refer to the software assist files for additional assistance.

3. Download and install the CD/DVD information recovery software.

   note:

   For this example, Ultra ISO is used. Refer to the software help files for additional assistance.

Extracting files

1. Start Total Commander by clicking Start, All Programs, Full Commander and then click Total Commander 32. If the non-registered version is used, follow the pop-up Windows instructions.

   note:

   For assistance and instructions on using Full Commander, view the Full Commander assist file.

2. Locate the downloaded SATA AHCI commuter using the directory construction in Total Commander. Select the SATA AHCI driver.

   Figure : SATA AHCI driver located

   

3. On the File Menu, click File and select Unpack Specific Files.

4. Type the target location to unpack the file.

   Figure : Enter unpack location

   

5. Locate the unpacked files.

6. Repeat the unpack process for F6flpy32.exe.

7. Open up the temp.IMA extracted from the F6flpy32.exe file using Ultra ISO or equivalent application.

   Effigy : temp.IMA driver files

   

8. Copy the temp.IMA driver files to a floppy deejay or fire the files to a CDROM.

Disable SATA native fashion

note:

This option is not available in the BIOS on Vista models.

1. Commencement the notebook PC.

2. Repeatedly press the F10 key (or fundamental designated by the notebook PC) until the notebook enters the Computer Setup screen.

3. Use the arrow keys to select System Configuration.

4. Use the arrow keys to select SATA Native Style and set the mode to Disable.

   Figure : Disable SATA Native Mode

   

5. Press the F10 key (or designated fundamental to accept the changes).

6. Salvage changes and exit Computer Setup.

7. The notebook should restart.

Installing Windows using native SATA drivers

To install Windows XP with native SATA driver, perform the following steps:

1. Boot the notebook PC.

2. Insert the Windows XP installation CD into the optical CD/DVD drive.

3. Printing the F6 key when prompted.

   Effigy : Third Political party Driver Prompt

   

4. Printing the S key to specify the boosted device.

   Figure : Specify Additional Device

   

5. Insert the SATA driver disk into drive A.

   Effigy : Insert Driver Disk

   

6. Follow the on-screen prompts.

Enable SATA native mode

1. During the starting of the notebook PC, repeatedly printing the F10 primal (or fundamental designated by the notebook PC) until the notebook enters the Computer Setup screen.

2. Apply the arrow keys to select Organisation Configuration.

3. Use the arrow keys to select SATA Native Fashion and ready the mode to Enable.

   Figure : Enable SATA native fashion

   

4. Press the F10 fundamental (or designated primal to take the changes).

5. Save changes and exit Computer Setup.

6. The notebook should restart.

RIS (Remote Installation Services)

This procedure is typically performed by It professionals over a network.

1. Download the latest "Intel Matrix Storage Manager" driver Afterwards downloading the "Intel Matrix Storage Manager" create one folder named Sata and re-create the iata61_enu.exe which you just downloaded from higher up mentioned link. Intel Matrix Storage Manager also includes SATA controller driver.

2. Use following command to extract the commuter files:

   c:\sata\ iata61_enu.exe -a -a -pc:\sata

   When run, the installation process begins; only click through the dialogs equally prompted. This volition not install the driver, it will but extract the commuter files to <c:\sata>. Later the extraction is completed, the commuter files can be institute in <c:\sata\Driver>.

3. Copy the extracted files to the RIS distribution point (on the RIS server):

   RemoteInstall\Setup<Linguistic communication>\Images\<Dir_Name>\i386

4. Copy the same files to:

   RemoteInstall\Setup<Linguistic communication>\Images\<Dir_Name>\$oem$\$1\drivers\sata

5. Open the RemoteInstall\Setup<Language>\Images\<Dir_Name>\i386\txtsetup.sif file with notepad, and add the following lines to the sections noted (section names are in brackets):

   

6. Save the file and exit notepad.

7. Open the Remote Install\Setup\<Language>\Images\<Dir_Name>\i386\templates\ristndrd.sif file with notepad, and under the section [Unattended] add together the post-obit lines:

   

8. Save the file and leave notepad.

9. Finally, to complete the process, end and restart the BINL service on the RIS server every bit follows:

   Go to a command prompt and type net stop binlsvc and press Enter. So type net start binlsvc and press Enter.

The RIS installation point has now been updated with the SATA driver.

Source: https://support.hp.com/id-en/document/c00758841

Posted by: tolartherect.blogspot.com

Share this post