How To Keep Jacuzzi Tub Jets Clean

Jetted tubs accumulate soap scum, biological materials, and other gunk in their jets over time. Whether you lot want to clean a jetted tub that hasn't been used in a while, or keep a tub that yous oftentimes utilise make clean, yous'll need to use some common household cleaners to have care of that grime. Use a special cleaning product to get rid of the more stubborn natural films, called biofilms, that build up in the jets and plumbing.

1
Fill the tub with hot water to ii–iii in (5.one–7.six cm) to a higher place the highest jets. Plow the hot water on and let it make full the tub. Turn information technology off when the jets are covered past 2–three in (5.1–vii.6 cm) of water.^[ane]
- Clean your jetted tub every 1-three months if yous use your tub daily or several times a week. Clean it at least one time every 6 months if you only use it a few times a month.
ii
Turn off the air induction valves by turning them fully clockwise. This forces the water to circulate only in the internal plumbing of the tub to concentrate the menstruum and clean deeper. Go out them open if the manufacturer of your tub states to do so in the owner's transmission.^[2]
- Always refer to manufacturer'southward instructions for cleaning your specific model of tub.
3
Add together 2 Us tbsp (xxx ml) of dishwashing liquid to the water. Use a low-foaming dishwashing liquid so you don't overflow the tub with bubbles. Apply four tbsp (56.7 yard) of powdered dish detergent if you don't take liquid detergent.^[3]
- The detergent will loosen greasy residue left behind in the jets past soap or chimera bath liquid.
4
Pour ⁱ⁄₂ cup (120 ml) of white vinegar or bleach into the tub. Cull vinegar for a more eco-friendly option. Use bleach if in that location is any mold present in the jets. But utilise ane or the other and do non mix them.^[iv]
- Both vinegar and bleach serve to disinfect during the cleaning.
5
Run the jets at full capacity for 10-fifteen minutes. Set the jets to the highest force per unit area and plough them on to make clean them out. You will see any gunk caught in the jets coming out into the h2o.^[5]
- If at that place is nonetheless crud coming out of the jets subsequently 15 minutes, then go on the jets on until it looks like no more dirt is coming out of them.
6
Drain the tub and refill it with common cold h2o. Make full the tub upwardly to 2–three in (v.ane–7.half dozen cm) above the jets once more, but with common cold water this time. Cold water is fine for the second bicycle because you are simply going to requite the jets a concluding rinse.^[6]
- Don't add together whatever cleaning products to the h2o this time. You only want clean, cold h2o for rinsing.
7
Run the jets for another x minutes on high ability. This volition remove all the last $.25 of residue that y'all loosened with the detergent and hot h2o. Brand sure no more gunk is shooting into the water before you lot turn the jets off.^[7]
- Let the tub run for another 5 minutes if it looks like the jets are still blasting out last $.25 of clay.
viii
Drain the tub and wipe it clean. Let all of the muddy water bleed out of the tub. Use a clean rag to wipe away any residue that is left on the surface of the tub.^[8]
- Yous can employ an sometime toothbrush to become into the crevices of the jets if there is anything lodged in them yet afterwards cleaning. Wipe them clean and rinse abroad the droppings later on doing so.
EXPERT TIP

James Sears leads the customer happiness team at Neatly, a grouping of cleaning gurus based in Los Angeles and Orange County, California. James is an adept in all things clean and provides transformative experiences by reducing clutter and renewing your dwelling environment. James is a current Trustee Scholar at the Academy of Southern California.

James Sears
House Cleaning Professional person

Try using a non-toxic approach with white vinegar and hot water. Fill the bathtub with hot h2o, then add white vinegar and run the jets on high for a few cycles. Drain the tub, then make full it once more with only water and run the jets to rinse out the vinegar. To deep clean mold and mildew, do the higher up steps using bleach instead of vinegar. Never use both bleach and vinegar together.

1
Get a biofilm removal liquid and read the instructions on the container. Purchase a biofilm removal liquid at a store that sells Jacuzzi and hot tub cleaning supplies, or online. Biofilm removal liquids are designed specifically to make clean away all the gunk that accumulates within the plumbing of a jetted tub.^[9]
- Biofilm is a natural film that is created by the buildup of bacteria, mold, mildew, and other biological materials.
- Cleaning your jetted tub with biofilm removal liquid is a method of cleaning to be used on its own, instead of cleaning your jetted tub with detergent and vinegar or bleach. You tin can use either method to regularly clean your tub effectively.
2
Make full the tub with hot water two–3 in (5.i–7.6 cm) to a higher place the jets. Turn the hot water on and let the tub fill until at that place is well-nigh two–3 in (5.1–7.6 cm) of h2o above the jets. Plow off the water so the tub doesn't fill anymore.
- Information technology's important that the jets are completely covered with water so that, when you turn them on, the motor doesn't get damaged and then they don't spray h2o up into the air.
3
Add the specified amount of biofilm remover to the water and plow the jets on. Pour in an corporeality of the cleaning liquid specified by the product's instructions. Plow the jets on at their highest ability to start circulating the cleaner.
- The biofilm cleaner's instructions may specify different amounts depending on if information technology is a regular cleaning or the beginning cleaning in a while.
four
Alternating running the jets and letting the tub sit down in xxx minute intervals. Always refer to the biofilm remover'southward instructions for any additional steps. Turn the jets on for 30 minutes, and so turn them off and let the tub sit for 30 minutes, so plow the jets back on for another xxx minutes earlier yous drain information technology to clean out the plumbing thoroughly.^[10]
- You can drain the tub and repeat this procedure if you want to requite it an extra expert cleaning.
5
Drain your tub and clean any balance around the sides. Utilize a clean rag or sponge to wipe away any gunk left on the surface afterward you drain it. Utilise a toothbrush or other pocket-sized castor to clean away annihilation that is stuck in or around the jets.
- Y'all tin can repeat the cleaning process some other time before you rinse the tub if it still looks dingy or if you desire to exist actress sure yous got everything out of the internal plumbing.
6
Refill the tub with cold h2o and run the jets for 10-15 minutes. This will rinse out the last of the gunk from the plumbing and rinse away any remaining biofilm remover. Drain the tub afterwards 10-xv minutes and give it a final wipe with a clean rag.^[11]
- Some manufacturers recommend doing this rinsing process after each use of the jetted tub to help get rid of soap scum, oils, dead skin, and other gunk that builds up after each utilize.
- Keep your jetted tub make clean by repeating this whole cleaning procedure approximately every v uses, regardless of how often y'all employ information technology.

Add New Question

Question

Can I utilize a tablet of dishwashing detergent when cleaning a jetted tub?

It may do the job, just scrub it thoroughly to exist sure it is make clean.
Question

If I merely employ the tub equally a bathtub will I still need to clean the jets?

Yes, as you bleed your tub, a small amount of water is left in the piping of the jets. As the h2o in the piping evaporates, it leaves deposits that creates mold.
Question

We never use the jets in the tub. Is at that place any manner to kill mold (or continue mold from forming) other than filling the tub, running the jets and refilling the tub?

Bill Soukup

Community Answer

You need to used a jetted tub cleaner to remove harmful contagion inside the plumbing lines. Even if you don't utilize the jets, h2o drains back into the lines and is a perfect convenance ground for leaner.
Question

How do I clean jets in an older tub that accept mold on them? I'm concerned that the h2o lines behind the jets have mold in them, too. The tub hardly ever is used for a bath. Just showers.

Bill Soukup

Community Respond

Y'all can find several proficient jetted tub cleaners on Amazon. These cleaners are designed to remove this type of contamination. Older tubs may take several cleanings since the old contamination may come off in layers and is more difficult to remove.
Question

Where do I become biofilm remover?

You can go it at puddle stores, places that sell hot tubs, or places similar Home Depot or Lowe's.
Question

How tin can I remove a tiny ring in my rarely used toilet?

Try a toilet cleaner make that is made for general use. Or use a scrub and a solution to scrub information technology off.
Question

How do I make my jets in my tub white again if they are xanthous?

Bleach and a toothbrush. Then rinse with cold h2o. Wear something to protect your pare, and nearly chiefly your optics.
Question

Tin can I use oxygen bleach when cleaning a jetted tub?

As long every bit the chemicals are friendly to rubber O-rings, all is OK. The pump has sealing O-rings, as well as the individual jets.
Question

Can my jet tub accept a piercing alarm?

Probably non. You lot might want to check on the pressure pump, as it might exist spinning a bearing or locked up on something. Piercing sounds warrant firsthand investigation!
Question

What can I use if I don't have powdered dishwasher detergent?

Gavin Donnelly

Customs Reply

You can use liquid dish detergent instead of powdered. Just use nearly half the amount.

Show more answers

Ask a Question

200 characters left

Include your e-mail address to become a message when this question is answered.

Submit

Open up doors and windows to ventilate the room as much as possible while using cleaning products. Bleach fumes can be dangerous in poorly ventilated areas.
Never use foaming cleaners or bubble bath in your tub. Bath oils and lotions leave residual in the pipes likewise. Y'all should avoid using them in a jetted tub.
Never start the jets unless they are covered by at least a few inches of h2o. If the jets are exposed, the motor volition exist damaged. If the jets are covered but the water is also shallow, they may spray water up, bathing your walls instead.
E'er refer to the manufacturer'due south instructions for specific cleaning instructions for your jetted tub.

Things You'll Need

2 Usa tbsp (30 ml) of dishwashing liquid or 4 tbsp (56.7 k) of powdered dish detergent
ⁱ⁄_two cup (120 ml) of white vinegar or bleach
Biofilm remover
Make clean rags
Toothbrush (optional)

About this article

Article Summary X

To clean a jetted tub, start by filling information technology with hot water so all of the jets are covered. Then, add 2 tablespoons of liquid dishwashing detergent to the h2o, followed by 1/2 loving cup of vinegar or bleach to disinfect the tub. Once yous've added everything, run the jets for 10-15 minutes then drain the tub. When all the water is out, refill the tub with cold water, and run the jets for an additional ten minutes to rinse out any remainder. Finally, bleed the tub and wipe it clean with a rag. To learn how to make clean a jetted tub with biofilm remover, scroll down!

Did this summary help y'all?

Cheers to all authors for creating a page that has been read 1,162,209 times.